New to this......How to set up service with MyGica 495 PRO box

[serpico]

Hi just just purchased a MyGica PRO 495 box and paid the donation on this site ( i received an email with some configurations) . I am new to this. My box is powered up and ready .... when i access KODI what do i do next? My box has KODI 16.1 installed ..... please tell me what i have to do to set up the service so i may watch TV channels ... thanks

[Dodgeit]

Here is a thread with instructions to set up Stalker Client and Epg.
https://iptvzeta.is/forum/nfps-iptv-...p-instructions

[Alex-levy]

I found the easiest way to set up Iptv on Android boxes is using STB emulator (download from play store) set up your portal check on "send id" register your Mac (@papiao site) given by your STB emulator restart the STB emulator and enter your ID and password (the 12 donation #s) and that all.kodi and all the add ons can be confusing for some.

[serpico]

Dodgeit - its not working ...... i will send a detail message in a few

[serpico]

i type a long reply and now it says "Edit Conversation Empty Response" and i cant post

[Dodgeit]

i type a long reply and now it says "Edit Conversation Empty Response" and i cant post

Lol don't type such a long message.

[serpico]

Dodgeit - thank you but it is still not working... its says: Stalker client authentication failed. I am using MyGica 495 PRO.

This is what is did ( i followed the instructions on the URL you sent above). I have copied and paste the info from the URL below so its easier to follow..... my response in red .

-Go to System Settings/Add Ons/My Add Ons/PVR Clients/Stalker Client. Done

***Note
The KODI Settings screen has 4 levels of access, located at the bottom left of the screen. To access all required settings, click the Tab until “Advanced" or "Expert” level is indicated.

-Select Configure - Done

-Set Portal 1 and Connection timeout to 120 - done but this was under the general tab

-Enter your MAC# done - but i had to tab over to portal 1 .... I followed the format below 00:1A:78: plus I used the last 6 characters on the MAC address on my box
Format Example( 00:1A:78:xx:xx:xx ) Replace the x’s, with your last digits from your STB’s MAC# or your PC /Apple/RasPi/Fire/DL-T/etc. MAC# …or
make up a random number in HEX from 00 to FF (Example: 2A:B9:43)

[serpico]

-Leave the Time Zone as is. Done

-Enter your Server Address (Info located from your donation information at Papiao
here -> hxxps://papiao.is/main/search_nfps (I have Kodi 16.1 and my server is 1.iptvprivateserver.tv so i used hxxp://portal1.iptvprivateserver.tv/stalker_portal/c/index.html - replaced hxxp with http)

*** Note Kodi 16 doesn't handle URL forwarding
If the server is 1.iptvprivateserver.tv then you would use hxxp://portal1.iptvprivateserver.tv/stalker_portal/c/index.html
If the server is 5.iptvprivateserver.tv then you would use hxxp://portal5.iptvprivateserver.tv/stalker_portal/c/index.html
etc.

-Enter your Login & Password - Done - according to my instructions on the email with my donation, the login and password is the same ,,, 12 numbers is this correct that they are both the same login and password?
(Login & Password both require your donation#)

-Enter a random Serial Number - should be a minimum 13 digit number (I use 6 numbers/1 Letter/ 6 numbers) done - i used 6 numbers random, one letter and another random 6 numbers

[serpico]

-Enter a random Device ID - Should be a minimum 12 digit number (I use numbers only) - Done - i used random 12 numbers

*(Token/Device ID2/Signature should be blank (at this time they are redundant fields)) Done

EPG info:
-Set to Prefer XMLTV There is nothing that says EPG but in the same configuration setting page it says preference and i selected XMLTV only

Remote URL: Done hxxp to http
URL Address :
hxxp://yahyabell.com

Save your settings by clicking OK, then Enable Stalker by clicking “Enable”. Done


* You Must now go to Papiao Site and "Associate" your MAC# you entered above, with your Donation#.
Once you have done that... Done


Go back to Settings/TV - General Tab - Done
-There are 3 settings regarding using Channel Numbers and Groups and Sync from the Back End. Enable all 3.

-Then Select "Enable". - done

Kodi should now attempt to connect. A message window in the top right corner of the screen will appear.
It will say "Loading Channels from Clients (if successful, Kodi will Include a "TV" Icon on the Menu Bar)
It will then Attempt to load the Guide. Let the system load everything before you attempt to watch TV.
If there is a problem, (Error Message at bottom right of Screen), Shut down and Restart KODI.- I restarted my box about 25 times its says Stalker client authentication failed.

If you still have problems, post your results.

[Dodgeit]

You have to make sure everything is set up right.You can't be off on any part of the instructions.So the first thing to do is go over all your settings and make sure they are correct.Then unplug the box log into your account and do a iptv reset.Then plug the box back in and load kodi.If your still having a problem you can pm me the donation info and i can test it for you.Do not post it here.

[Dodgeit]

Well what you did was copy and paste the instructions.Just follow them like i said make sure everything is right.Many of members have used the same instructions and it worked so there is a problem in what you are doing or there is something wrong with the donation.But 99% of the time it's user error.

[serpico]

ok i will try again and let you know..... thanks for helping ( i just want it to work)..... will let you know.

[serpico]

i reset to factory settings and i uninstalled Kodi 16.1 and installed Kodi 17 and it's working now ..... thanks all and Dodgeit

[Dodgeit]

Glad you got it working.